Calibrate a wide range of pressure gauges and sensors from very low pressure to 3000 psi with this reliable, easy-to-maintain pressure calibrator
Unsurpassed rangeability in one pressure controller / calibrator: install up to five measurement modules with uncertainty as good as 0.01% reading from 30% to 100% of the modules span.
Configure for todays requirements, expand later as your needs change and grow. Add modules to increase the pressure range or accuracy in seconds, without needing to return the instrument to the factory.
Optional contamination prevention system helps you avoid risk of contaminating your pressure standard when calibrating hydraulic devices.
The 6270A features pressure ranges from low differential pressure to 20 MPa (3000 psi), which covers the requirements of most gauges and sensors. Three levels of accuracy, 0.02 % FS, 0.01 % reading from 50% to 100 % or 0.01 % reading from 30 % to 100 %, let you balance your need for accuracy with the limits of your budget.
Thanks to its modular design, the 6270A is flexible enough that you can install modules with different accuracy classes within the same chassis. You can buy the highest level of accuracy for the pressure ranges that require it and a lower, more economical level of accuracy where applicable.
|
General specifications |
|||
|
Power requirements |
100 V ac to 240 V ac, 47 Hz to 63 Hz |
||
|
Fuse |
T2A 250 V ac |
||
|
Max power consumption |
100 W |
||
|
Operating ambient temperature range |
15 °C to 35 °C |
||
|
Storage temperature |
-20 °C to 70 °C |
||
|
|
Storage: <95 %, non-condensing. A
power stabilization period of four days may be required after extended
storage at high temperature and humidity. |
||
|
Vibration |
MIL-T-28800E |
||
|
Altitude (operation) |
<2000 m |
||
|
Ingress protection |
IEC 60529: IP20 |
||
|
Safety |
IEC 61010-1, Installation Category
II, Pollution degree 2 |
||
|
Weight (Chassis only) |
13 kg (28.5 lbs) |
||
|
Dimensions |
Height: 147 mm (5.78 in) |
||
|
Rack mount dimensions |
3U-19 inch rack |
||
|
Warm up time |
15 minutes after power up or module
installation, when items previously stored within Operating Ambient
Temperature Range. |
||
|
Calibration |
ISO/IEC 17025 accreditation |
||
|
Control specifications |
|
||
|
|
PM500, ranges ≤ 20 kPa (80
inH20) ± 0.002% range |
||
|
|
All other ranges ± 0.001% range |
||
|
Control turndown1 |
10:1 (typical) |
||
|
Low control point |
1 kPa (0.15 psi) absolute |
||
|
Supply pressure requirements |
|
||
|
Clean dry N2 or air –
Industrial grade nitrogen, 99.5 %+ |
|
||
|
Particulate contamination |
≤ 1.25 micrometer (50 microinches) |
||
|
Maximum moisture content |
-50 °C dew point |
||
|
Maximum hydrocarbon content |
30 ppm |
||
|
Vacuum supply requirements (when
operating near or sub-atmospheric) >50 liters per minute
capacity with Auto Vent feature
Appropriate protections for High Pressure Gauge work system exhaust
gas will pass through the Vacuum supply system. |
|||
|
Interface/communications |
|||
|
Primary remote interfaces |
IEEE 488.2, Ethernet, RS232, USB |
||
|
System connection |
Supports interconnection of two or
three systems |
||
|
Switch test connection |
Standard 4 mm jack: |
||
|
|
Nominal 24 v dc isolated drive
Maximum 30 V dc w.r.t. chassis ground |
||
|
Aux drivers |
4 external solenoid drivers |
||
|
|
24 V dc drive (maximum drive 6 W
continuous per channel) |
||
|
Model Name |
Description |
|
6270A |
Pressure Controller/Calibrator |
|
6270A-NPT |
Modular Pressure Controller Chassis,
NPT Manifold |
|
6270A-BSP |
Modular Pressure Controller Chassis,
BSP Manifold |
|
6270A-7/16 |
Modular Pressure Controller Chassis,
SAE 7/16-20 Manifold |
|
BRM600-BA100K |
Barometric Reference Module, 70 to
110 kPa (10 to 16 psi) |
|
PCM-STD-20M |
Pressure Control Module, Standard
Turndown |
|
Accessories common to all models: |
|
|
Accessory |
Description |
|
Accessory |
Description |
|
PM200 Pressure Measurement Modules |
For 2271A Industrial Pressure
Calibrator, and 6270A, 8270A and 8370A Pressure
Controller/Calibrators |
|
PM500 Pressure Measurement Modules |
For 2271A Industrial Pressure
Calibrator and 6270A, 8270A and 8370A Pressure Controller
/ Calibrators |
|
PM600 Pressure Measurement Modules |
For 6270A, 8270A and
8370A Pressure Controller/Calibrators |
|
RMK-XX70 |
Rack mount Kit, 19 In Width, 3U |
|
CASE-6270 |
Shipping Case, 6270A |
|
CASE-PMM |
Shipping Case, 3 PMM Modules |
|
PK-6270-NPT |
Lines and Fittings Kit, 6270A NPT |
|
PK-6270-BSP |
Lines and Fittings Kit, 6270A BSP |
|
CPS-40M-HC40 |
Contamination Prevention System, 40
MPa (6000 psi), with HC40 test port and hand tight adaptors |
|
TST-40M-HC40 |
Test Station, Std Port/Adaptors |
|
VA-PPC/MPC-REF-110 |
Vacuum Pump Package, 110 V |
|
VA-PPC/MPC-REF-220 |
Vacuum Pump Package, 220 V |
|
CDG-REF-1TORR |
Capacitance Diaphragm Gauge for
zeroing of Absolute Mode PM500 Modules |
|
PK-PMM-ZERO |
Interconnection Kit for zeroing of
Absolute Mode PM500 Modules |
